Sage Posted April 12, 2018 Share Posted April 12, 2018 As I was unsure of what T14 was (perils of being new-ish to fly fishing) thought this may help other forum members.... "T-14 is a very versatile material for constructing sinktips used when Skagit casting. The ’14’ means 14 grains per foot – it’s pretty bulky and sinks pretty fast, and it’s great for turning over and then sinking the big flies that are most often used when fishing in the Skagit style. Unfortunately pre-made T-14 tips aren’t readily available, and that means you need to cut the lengths that you want to fish and put loops on both ends. Rio sells T-14 in bulk spools as well as in packs that combine 30 feet of T-14 with some braided mono loops to be attached to the tip. Unless you’re going to turn your basement into a tip factory, the 30-foot packs probably work just fine." Source: Deneki.com Quote Link to comment Share on other sites More sharing options...
toolman Posted April 12, 2018 Share Posted April 12, 2018 Yes, it does get snagged under rocks sometimes and you will loose Flys. The egg sucking leech patterns that I use are unweighted for these deep slow presentations. A shallow angled down and across cast will help eliminate arc at the tip, but often where the current speed is fast enough, a slightly upstream and across presentation allows enough drift time to get the fly down deep, and the faster edges of midstream current will get the fly below the tip, eliminating some, but not all of the arc in the tip. I believe it creates a more natural presentation. The key is to go slow. Let it arc out and stop. No rush to start stripping back as the fly is now in the strike zone. Most often I just let it sit there for a bit before starting the retrieve. Leeches generally move very, very slowly. . . Depending on the terrain, 12' of T-14 or T-10 may do the job just as well when the water is shallower and/or current speed is slower. 2 Quote Link to comment Share on other sites More sharing options...
bcubed Posted April 12, 2018 Share Posted April 12, 2018 15 feet of t14 and the associated rod required to throw it for trout fishing.. Quote Link to comment Share on other sites More sharing options...
toolman Posted April 12, 2018 Share Posted April 12, 2018 Yes certainly a two hander job, but with the abundant choices of short shooting heads, pretty easy with a 12' 6 wt. In response to the original post about fishing egg patterns on the Bow. It's important to recognize that brown and Rainbow trout eggs are dense and sticky. They don't tend to drift very far from the nest site and the trout guard them fiercely for a week or two after spawning, so its not likely trout see a lot of eggs in the drift outside of brief spawning periods. Eggs that remain unfertilized may eventually drift off as they decay. They are usually translucent, pale white. 2 Quote Link to comment Share on other sites More sharing options...
Jayhad Posted April 23, 2018 Share Posted April 23, 2018 I fish a hunk of T12 on my 2WT and I never see it get hung up..... if someone would just make a streamer taper for a 2wt I wouldn't have to mickey mouse it Quote Link to comment Share on other sites More sharing options...
SilverDoctor Posted April 24, 2018 Share Posted April 24, 2018 Nothing wrong with Micky Mousing. As an example many of us where using short shooting heads many years before they became vague buy cutting down Spey heads. Quote Link to comment Share on other sites More sharing options...
Dangus Posted April 24, 2018 Share Posted April 24, 2018 18 hours ago, Jayhad said: I fish a hunk of T12 on my 2WT and I never see it get hung up..... if someone would just make a streamer taper for a 2wt I wouldn't have to mickey mouse it How many feet long is your tip? Quote Link to comment Share on other sites More sharing options...
Jayhad Posted April 24, 2018 Share Posted April 24, 2018 26 minutes ago, Bron said: How many feet long is your tip? 18" Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.