fishpro Posted May 21, 2019 Share Posted May 21, 2019 So I purchased a second hand aluminum boat today, and am looking for suggestions for an anchor system, hopefully one that I can operate myself from the back of the boat. Does anyone have any suggestions on what and where to buy? Secondly, what would be the best way to set this up? Running along the side of the boat, along the floor (would probably need to be covered), or any other ideas? Thanks for any suggestions you can provide! Quote Link to comment Share on other sites More sharing options...
BrianR Posted May 21, 2019 Share Posted May 21, 2019 I used 2 25 lb pyramids for my old 1756 jon boat.Using scottie anchor locks, 50' of braided marine rope,11/2feet of galv.chain.When it was windy i added the same on the opposite side.So in this case 1 out front,1 on ea.corner This boat had a lot of surface are & ,mostly flat & close to the water.V hull you might get away with less,of course wind being the major factor...Play safe Quote Link to comment Share on other sites More sharing options...
Sparkplug Posted May 21, 2019 Share Posted May 21, 2019 So I'm going to go a bit contrarian here...I have a 12' alum boat and I run it with only one anchor, off the bow. Let the boat windmill in the wind - in big wind/waves (which for a 12' boat, don't need to be all that large in order to feel big) it keeps the bow pointed into the wind/waves, which is good for safety/stability. I like to cover a lot of water when I fish from an anchored position, so letting the boat windmill around is somewhat helpful in that regard. I also often fish multiple-fly rigs (where allowed) and more than once, I'm somewhat ashamed to admit, I've had a fish break me off by dragging the line over the anchor rope, and getting one of the other flies on the rig caught on the anchor rope (can't always keep those big ones away from the anchor rope during the fight). I imagine this would be more of a risk when two or more anchor lines down. I should note that most of my fishing in this boat is by my lonesome, so I can cast wherever when the boat is windmilling. If more than one person in the boat, better fixing of the boat via multiple anchors may be desirable. Quote Link to comment Share on other sites More sharing options...
Dangus Posted May 21, 2019 Share Posted May 21, 2019 1 hour ago, Sparkplug said: So I'm going to go a bit contrarian here...I have a 12' alum boat and I run it with only one anchor, off the bow. Let the boat windmill in the wind - in big wind/waves (which for a 12' boat, don't need to be all that large in order to feel big) it keeps the bow pointed into the wind/waves, which is good for safety/stability. I like to cover a lot of water when I fish from an anchored position, so letting the boat windmill around is somewhat helpful in that regard. I also often fish multiple-fly rigs (where allowed) and more than once, I'm somewhat ashamed to admit, I've had a fish break me off by dragging the line over the anchor rope, and getting one of the other flies on the rig caught on the anchor rope (can't always keep those big ones away from the anchor rope during the fight). I imagine this would be more of a risk when two or more anchor lines down. I should note that most of my fishing in this boat is by my lonesome, so I can cast wherever when the boat is windmilling. If more than one person in the boat, better fixing of the boat via multiple anchors may be desirable. Do you think Spinning around and losing the depth at where your fly is fishing (esp bobber fishing) is going to cost you more fish than how many you get hung up on a second anchor rope? 1 Quote Link to comment Share on other sites More sharing options...
Brunsie Posted May 21, 2019 Share Posted May 21, 2019 I think 15lb anchors would hold you just fine. I've always figured if I'm getting blown off my anchors, it's too windy to fish any way. As far as two anchors go, indy fishing with only one lets your boat slew around and it doesn't take very long to get big bellies in your line, causing a lot of casting 2 Quote Link to comment Share on other sites More sharing options...
stein Posted May 22, 2019 Share Posted May 22, 2019 depending on your budget, minn kota deckhand is pretty slick, have one myself, pulls a 40lb anchor, and has a remote (corded) operating switch. Quote Link to comment Share on other sites More sharing options...
Sparkplug Posted May 22, 2019 Share Posted May 22, 2019 22 hours ago, Bron said: Do you think Spinning around and losing the depth at where your fly is fishing (esp bobber fishing) is going to cost you more fish than how many you get hung up on a second anchor rope? The boat generally doesn't move around that much, such that my target casting area generally is always within range. Quote Link to comment Share on other sites More sharing options...
fishpro Posted May 26, 2019 Author Share Posted May 26, 2019 Thanks for the suggestions everyone, I went with the Minn Kota Deckhand which I now have mounted on the front of my boat. 1 Quote Link to comment Share on other sites More sharing options...
screaminreel Posted May 29, 2019 Share Posted May 29, 2019 All you need is a 15 - 20 lb anchor front and 12 - 15 lb at the back. Don't use just one anchor. Scotty mounts are great. Quote Link to comment Share on other sites More sharing options...
northfork Posted May 29, 2019 Share Posted May 29, 2019 15 -20 front and back. Scotty anchor locks. End. 1 Quote Link to comment Share on other sites More sharing options...
monger Posted May 31, 2019 Share Posted May 31, 2019 2 anchors for bobber fishing is often a very good idea. Especially early season with cold water Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.