Timo Posted February 17, 2011 Share Posted February 17, 2011 Just wondering if someone has tips for me on the whip finishing trick(if there is one) between the spun deer hair and the cone? From all the pictures I see of the bow river bugger with a conehead the spun and clipped deer hair seamlessly meets with the cone. I am going to tie some tonight and I am looking for any tricks of the trade regarding this one aspect of the fly. I can tie them without a conehead but I am foreseeing some difficulty. Is the trick just the way you hold out your tongue when finishing it off? Can you effectively get head cement in there? example (not mine) of the clean look I am wanting to achieve Quote Link to comment Share on other sites More sharing options...
Flytyer Posted February 17, 2011 Share Posted February 17, 2011 Whip finishing shouldn't be much of a problem. Care must be taken not to cut the thread on the cone, going slower than you normally would should help. As for cement I would recommend not using it but waxing the thread before whip finishing should be ok for holding the thread locked. With practice you'll get it. Quote Link to comment Share on other sites More sharing options...
Timo Posted February 17, 2011 Author Share Posted February 17, 2011 Whip finishing shouldn't be much of a problem. Care must be taken not to cut the thread on the cone, going slower than you normally would should help. As for cement I would recommend not using it but waxing the thread before whip finishing should be ok for holding the thread locked. With practice you'll get it. Thanks, I will give it a try. Quote Link to comment Share on other sites More sharing options...
Crogg Posted February 17, 2011 Share Posted February 17, 2011 I would put a little head cement on the thread and then whip finish Quote Link to comment Share on other sites More sharing options...
SouthBow Posted February 17, 2011 Share Posted February 17, 2011 Just wondering if someone has tips for me on the whip finishing trick(if there is one) between the spun deer hair and the cone? From all the pictures I see of the bow river bugger with a conehead the spun and clipped deer hair seamlessly meets with the cone. I am going to tie some tonight and I am looking for any tricks of the trade regarding this one aspect of the fly. I can tie them without a conehead but I am foreseeing some difficulty. Is the trick just the way you hold out your tongue when finishing it off? Can you effectively get head cement in there? example (not mine) of the clean look I am wanting to achieve Just add a little Zap a Gap to your last few wraps of thread before you tie off that will hold the life of the fly Quote Link to comment Share on other sites More sharing options...
Guest 420FLYFISHIN Posted February 18, 2011 Share Posted February 18, 2011 with you bobin hand pull the HD back and the whip finish should slide down to the center. 3 should do with out creating a void. Quote Link to comment Share on other sites More sharing options...
KnotLikely Posted February 19, 2011 Share Posted February 19, 2011 If you don't clip your deer hair before you spin it, you'll have a bit of a handle to pull the collar back giving you some room to throw on a few half hitches or a whip finish. Before you do that, do like Southbow says, and add some zap-a-gap, or head cement to your thread and then half hitch or whip finish. With the technique Southbow describes using zap-a-gap, you don't even have to half hitch or whip finish, but if I have the room I like to throw on a few half hitches or a whip finish. I usually let the zap-a-gap or head cement dry before clipping to keep things neat. A sharp razor will also tend to give you a nicer more even cut than trimming with scissors. Leaving the deer hair long, you can again use it as a handle when trimming to avoid cutting off your flared collar. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.